Speaker wire how much to strip

The white and the black are both on silver wires, the blue and the red are both on gold wires. I wish I could put a photo here. I have too many wires for the screws.

Help is greatly appreciated. Hi there it would be better to email me directly especially with photos if possible. You can find my contact info on my Contact page. I have a golf 3 cabriolet and I recently bought some new speakers, now I dont know much about wiring and it seems the dash speakers are connected with 4 wires, while the new speaker I want to install only has a pos and neg tabs.

How could I adjust the wiring so my new speakers fit the dash? Any help is much appreciated :. I have Monster Cable speaker wire with metal pin ends. This is for a home stereo. They have worked fine for all applications for many years.

My wife just purchased a hybrid tube preamp. The speaker terminals are RCA only. They are connected as one. This results in four actual connections. I apologize for being so wordy. Any input no pun intended from you would be wonderful, and I thank you so much. Which is negative? How do I check if a speaker wire is positive or negative? Connecting speaker wire together with crimp terminals 2. Connecting speaker wire together by soldering How to connect speaker wire to a home stereo receiver or amplifier Connecting speaker wire to a receiver or amplifier with binding posts How to connect speaker wire to a receiver or amplifier with banana plugs Using a spade connector set How to connect speaker wire to banana plugs 1.

How to use speaker wire with set screw banana plugs 2. How to use speaker wire with binding post type banana plugs How to make RCA cable speaker wiring connections Make your own RCA speaker cable RCA plug to speaker wire diagram How to connect speaker wire to spring clip terminals How to connect speaker wire to car or home speakers Solder vs crimp terminals for connecting speaker wire Instructions for connecting speaker wire to car and home speakers How to connect a subwoofer with speaker wire How-to steps and images More helpful articles.

Your comments are welcome! Any help is much appreciated : Reply. Used a Stanley knife and then pulled off the cut cover with my teeth and my front crown came out with the wire.

That must have been quite a shock! My main concern will be not slicing my thumb as I try force a rather blunt knife to cut through the cable sheath. I knew I should have got a sharp knife instead of another useless cable stripper. Like yourself I've never got on with any of the cable stripping tools except for the small plastic ones you use on Cat5 cable and the like and that was superb but I don't think it would work with a thicker wire at all.

God bless good old Stanley No idea if this is reccomended, but I just use a pair of scissors and an extremely steady hand. Suppose it all depends on dexterity, but if you're good with your hands I can't see it being a problem as long as you're carefull.

Works for me. Cheers S. Slackadder Active Member. Agree with Oly, I have used proper tools before but the QED XT I use for surrounds is bloody tough not compliant like the softer Chord stuff so a pair of scissors, a steady hand and a lot of patience will do the job!

Last edited: Jul 5, I think the easiest way is with a stanley knife. I slice down the centre of the length of the cable, then peel it back then cut the sheathing off. You dont risk cutting you fingers this way.

Magic Beans Member. Nothing else does the job so well. Just watch the fingers. Unknown Standard Member. Worked like a charm on the separated cables.

I had a look on the RS sight and apparently they're not that cheap, but for hassle free stripping I'd say it's totally worth it! Make sure to do this carefully and not too roughly, to prevent the wire from being damaged.

You can get your speaker cable ready to use in 3 simple steps. After that, you can connect the speaker cable to your other speakers and receiver. Business Stores Customer Service. Written by Stan 29 June How do I strip my speaker cable? In this article, we'll explain how to strip a speaker cable in a few simple steps. A speaker cable consists of a left and a right side.

Each side consists of 2 separate wires. So, a speaker cable contains a total of 4 separate wires. These wires all need to be stripped in order to connect the speaker to your your receiver and other speakers. You'll need a wire stripper for this.